| Technical Specifications |
| Capacity |
Beltpacks per Base Station: 16 BPs (FSII or FSE) |
| Transceivers/Antennas Supported by Base: 6 x IPT or FSE TCVR and 10 x E1 TCVRs (1.9 or 2.4GHz) |
| Headset Microphone Input |
Input Type: Dynamic /Electret – Selectable |
| Frequency Response: Headset Mic – Partyline: 200Hz – 12kHz + 3dBu |
| Frequency Response: Headset Mic – Line Out: 200Hz – 20kHz + 3dBu |
| Mic Limiter Threshold: -50dBu ±3dB |
| Mic Limiter Range: ≥ 20dB |
| Max Input Level: -25dBu |
| Input Level: -60dBu nominal; -25dBu MAX |
| Headset Mic Voltage: 5V (Electret selectable) |
| Headset Output |
Load Impedance: > 32Ω |
| Output Impedance: 33Ω |
| Max Output Level before Distortion: > 13dBu |
| Total Harmonic Distortion (THD): < 0.1% THD at 1kHz |
| Headset Mic – Partyline: -78dBu (Clear-Com mode) |
| Headset Mic – Line Out: -60dBu |
| Frequency Response: Partyline – Headset Out: 200Hz – 10kHz + 3dBu |
| Audio/Radio |
4-wire I/O: Output Impedance >10kΩ, Input Impedance 200Ω + 10%, transformer isolated balanced input and output. |
| 4-wire Operating Levels: 0dBu Nominal, 18dBu headroom |
| 2-wire I/O: Selectable RTS or Clear-Com mode, Software controlled auto-null, null depth >60dB at 1kHz |
| 2-wire Operating Levels: -18dBu nominal (Clear-Com Mode), -12dBu nominal (RTS Mode), Headroom 18dB |
| Frequency Response Base-to-Beltpack: |
| Freespeak Edge Beltpack: 200Hz – 12kHz, |
| Freespeak II Beltpack: 200Hz – 7.1kHz |
| Partyline I/O |
2W Power On/Off: A/B, C/D paired- software controlled |
| 2W Output Voltage: 25 – 28V DC, 560 mA per pair (A/B or C/D) |
| 2W Impedance: >10kΩ |
| 2W Frequency Response: 200 to 12kHz. ±3dB |
| 2W Total Harmonic Distortion (THD): < 0.1% THD at 1 kHz |
| Relay Contacts or GPIO |
Connector Type: 2 x DB9 |
| Relay Contact Type: SPDT |
| Relay Quantity: 4 |
| Relay Contact Voltage Rating: 30V DC |
| Relay Contact Current Rating: 1A |
| Input Type: Opto-Isolated |
| Input Quantity: 2 |
| Input Voltage Range: 4 – 30 volts DC or AC |
| Input Current: >=1.2mA required |
| Connectors |
4-wire I/O: (8) RJ45 |
| 2-wire I/O: (4) XLR-3F |
| Program Input: XLR-3M, provided using cable assembly CAB-RJ45-PGM-SA |
| Stage Announce Output: XLR-3F, provided using cable assembly CAB-RJ45-PGM-SA |
| Headset: Free speak Edge Base: 4-pin XLR-M, auto headset detect |
| USB: USB type A Receptacle |
| Number of E1 antenna ports: 2 x RJ45, 2 x Fiber (2 active at any time) |
| DECT Radio frequency sync: Rear RJ45 input and output RF sync connectors |
| Indicators and Function |
Displays: (2) 480 x 128 color TFT LED Touch Screen displays |
| Front Panel Indicators & Function: |
| (2) Power Supply Status LEDs |
| (1) Status LED (Edge) |
| (1) Three Color Level Control LED Array |
| Power: |
| AC Mains input: 100-240V AC, 50-60Hz, 160W Max, IEC60320 C14 inlet. |
| DC Low Voltage Input: 12V DC +/- 5%, 12A |
| External AC/DC Power Supply (453G020-1 Supplied): |
| Input: 100-240V AC, 50-60Hz, 2.2A Max, IEC60320 C14 inlet. |
| Output: 12V DC +/- 5%, 12.5A |
| Environmental |
Operating: 32° to 113°F (0° to 45°C) |
| Storage: 86° to 158°F (30° to 70°C) |
| Humidity: 20-90% Non-Condensing |
| Dimensions |
1RU |
| 19 x 1.72 x 13.929in (WxHxL) |
| (43.6 x 482.6 x 353.8mm) |
| Depth: 260mm |
| Weight: 7.25lbs (3.29kg) |
| Network Specifications |
| AoIP Interfaces |
Protocols: |
| RTSP/SAP |
| AES67 |
| Dante |
| Audio Sampling: 24 bit Linear 48KHz |
| IP Addressing: Static, DHCP |
| Network Compatibility: Layer 2 & 3 LAN only |
| Quality of Service: DiffServ RFC2474 |
| IGMP: On (AoIP) |
| Multicast: On (AoIP) |
| Network Timing: PTPv2 (AoIP) / PTP v1 (Dante) |
| Minimum Network Bandwidth Required |
| Perduplex Connection: |
| 1 x FS II IPT bandwidth usage: ~7 Mbps. |
| 1 x FS Edge IPT: ~ 9.6 Mbps |
| Network Protocols |
| Ethernet IPv4 Unicast Audio and Control |
| mDNS–Multicast Device Discovery |
| Network Ports |
Unicast: |
| Port 80 TCP–Web Interface, System Management, Expansion |
| Port 443 for HTTPS |
| Port 6001 UDP–AES67 Data |
| Port 15000 – 15256 UDP – AES67 Audio |
| Multicast: Port 5353 UDP–mDNS, Names, Discovery, Linking, Expansion, Dante (through various ports) |
| Network Jitter Tolerance: < 1us required for RF Syncing of Transceivers |
| Recommended Ethernet Switches |
Managed Ethernet Switch – Layer 3 |
| 100/1000 Base-T ports for endpoints |
| 1000 Base IP Trunks between switches |
| QoS Configuration |
| Energy Efficient Ethernet bypass option |
| IGMP Snooping bypass option |
WhatsApp us 
Reviews
There are no reviews yet.